- 您现在的位置：买卖IC网 > Sheet目录480 > MT9P031I12STM (Aptina LLC)SENSOR IMAGE 5MP MONO CMOS 48LCC
MT9P031: 1/2.5-Inch 5-Mp Digital Image Sensor
Functional Overview
Table 2:
Pin Descriptions
Name
RESET#
LLCC Pin
16
Type
Input
Description
When LOW, the MT9P031 asynchronously resets. When driven HIGH, it
resumes normal operation with all configuration registers set to factory
defaults.
EXTCLK
SCLK
OE#
31
4
17
Input
Input
Input
External input clock.
Serial clock: Pull to V DD Q with a 1.5 K Ω resistor.
When HIGH, the PIXCLK, D OUT , FRAME_VALID, LINE_VALID, and STROBE
outputs enter a High-Z. When driven LOW, normal operation resumes.
STANDBY#
14
Input
Standby: When LOW, the chip enters a low-power standby mode. It
resumes normal operation when the pin is driven HIGH.
TRIGGER
15
Input
Snapshot trigger: Used to trigger one frame of output in snapshot
modes and to indicate the end of exposure in bulb exposure modes.
S ADDR
S DATA
PIXCLK
13
5
32
Input
I/O
Output
Serial address: When HIGH, the MT9P031 responds to device ID (BA) H .
When LOW, it responds to serial device ID (90) H .
Serial data: Pull to V DD Q with a 1.5 K Ω resistor.
Pixel clock: The D OUT , FRAME_VALID, LINE_VALID, and STROBE
outputs should be captured on the falling edge of this signal.
D OUT [11:0]
33 to 45
Output
Pixel data: Pixel data is 12-bit. MSB (D OUT 11) through LSB (D OUT 0) of
each pixel, to be captured on the falling edge of PIXCLK.
FRAME_VALID
7
Output
Frame valid: Driven HIGH during active pixels and horizontal blanking
of each frame and LOW during vertical blanking.
LINE_VALID
8
Output
Line valid: Driven HIGH with active pixels of each line and LOW during
blanking periods.
STROBE
9
Output
Snapshot strobe: Driven HIGH when all pixels are exposing in
snapshot modes.
V DD
V DD Q
D GND
V AA
VAAPIX
A GND
V DD PLL
TEST
RSVD
NC
12, 7
11, 39
10, 26, 46
23, 24
1, 48
2, 22
25
3, 20, 21
6
18, 19, 27, 28, 29,
Supply
Supply
Supply
Supply
Supply
Supply
Supply
–
–
–
Digital supply voltage: Nominally 1.8V.
IO supply voltage: Nominally 1.8V or 2.8V.
Digital ground.
Analog supply voltage: Nominally 2.8V.
Pixel supply voltage: Nominally 2.8V, connected externally to V AA .
Analog ground.
PLL supply voltage: Nominally 2.8V, connected externally to V AA .
Tie to A GND for normal device operation (factory use only).
Tie to D GND for normal device operation (factory use only).
No connect.
30
PDF: 09005aef824c993e/Source: 09005aef824c9943
MT9P031_5100_PB_2.fm - Rev. B 8/07 EN
6
Micron Technology, Inc., reserves the right to change products or specifications without notice.
?2006 Micron Technology, Inc. All rights reserved.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MT9P401I12STC
SENSOR IMAGE CMOS 5MP 48LCC
MT9T001P12STC
IC SENSOR IMAGE COLOR 48-PLCC
MT9V032C12STM
SENSOR IMAGE VGA MONO CMOS 48LCC
MTB2P50ET4G
MOSFET P-CH 500V 2A D2PAK
MTB30P06VT4
MOSFET P-CH 60V 30A D2PAK
MTB50P03HDLT4
MOSFET P-CH 30V 50A D2PAK
MTB75N05HDT4
MOSFET N-CH 50V 75A D2PAK-3
MTCBA-C1-N3
MODEM CDMA RS232 DUAL
相关代理商/技术参数
MT9P031I12STMD ES
功能描述:KIT DEV FOR MT9P031 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:Micron®DigitalClarity® 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:1 系列:-
MT9P031I12STM-ES
制造商:Aptina Imaging 功能描述:Image Sensor Monochrome CMOS 2592x1944Pixels 48-Pin LCC
MT9P031I12STMH ES
功能描述:KIT HEAD BOARD FOR MT9P031 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:Micron®DigitalClarity® 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:1 系列:-
MT9P031I12STM-SAMPLE
制造商:Aptina Imaging 功能描述:SAMPLES. NOT FOR SALE.
MT9P401I12STC
功能描述:SENSOR IMAGE CMOS 5MP 48LCC RoHS:是 类别:传感器，转换器 >> 图像，相机 系列:DigitalClarity® 标准包装:480 系列:- 象素大小:6.7µm x 6.7µm 有源象素阵列:768H x 488V 每秒帧数:52 电源电压:3.3V 类型:CMOS 成像 封装/外壳:48-QFP 供应商设备封装:48-QFP 包装:托盘 请注意:* 配用:4H2105-ND - HEADBOARD FOR KAC-004014H2104-ND - KIT EVAL FOR KAC-00401 其它名称:4H20954H2095-NDKAC-00401-CBC-LB-A0
MT9P401I12STCH ES
制造商:Aptina Imaging 功能描述:
MT9-PC
制造商:Tamura Corporation of America 功能描述:
MT9RTF12872FZ-667H1D6
制造商:Micron Technology Inc 功能描述:1GB 128MX72 DDR2 SDRAM MODULE PBF DIMM GREEN 1.55V FUL BUF - Trays